Electrical characteristics
D-FS100LD/20C系列 | 001LD | 005LD | 010LD | 020LD | 030LD | 040LD | 050LD | 100LD |
额定电流IPN(mA) Primary nominal input current | 1 | 5 | 10 | 20 | 30 | 40 | 50 | 100 |
测量范围IP(mA) Measuring range ofprimary current | 0... ±1.5 | 0... ±7.5 | 0... ±15 | 0.. ±30 | 0... ±45 | 0.. ±60 | 0... ±75 | 0.. ±150 |
输出电压Vo Output voltage | 输出额定值±5V, 对应原边额定电流 The output rating is ±5V, corresponding to the rated current of the primary side | |||||||
精度Ae Precision | ±1% | |||||||
电源电压Vco Supply voltage | ± 12...15V(±5%) | |||||||
绝缘电压V Insulation voltage | 在原边与副边电路之间：50Hz,1min,3KV Between the primary and secondary side circuits: 50Hz,1min,3KV | |||||||
失调电压Voff Offset voltage | 当原边电流IN=0时，最大值：±30mV When the primary current IN=0, the maximum value is ±30mV | |||||||
温漂VoT Thermal drift of V0 | 最大值：±1mV/℃ Maximum value: ±1mV/℃ | |||||||
线性度Le Linearity | ≤±1% | |||||||
反应时间Tres Response time | ≤20ms | |||||||
工作温度TA Ambient operating temperature | -10℃...+85℃ | |||||||
贮存温度T Ambient storage temperature | -40℃..+85℃ | |||||||
负载电阻RL Load resistance | >2KΩ | |||||||
Dimensions of drawing(mm)
Remarks：
1. When the current to be measured passes through the sensor, the voltage can be measured at the output end. (Note: Incorrect wiring may cause sensor damage)
2. The output amplitude of the sensor can be adjusted according to the needs of the user;
3. Sensors with different rated input current and output voltage can be customized according to user requirements.
| Classify | Title | Download |
|---|
Leave your contacts and our engineers will help you to find the solution you are looking for.
Open loop current sensor based on the principle of Hall-effect. It can measure the AC signal current under the condition of electrical isolation and convert it into DC signal output.
KNOW MORE
Open loop current sensor based on the principle of Hall-effect. It can measure the AC signal current under the condition of electrical isolation and convert it into DC signal output.
KNOW MORE
Op en loop current sensor based on the principle of Hall-effect. It can measure the AC signal current under the condition of electrical isolation and convert it into DC signal output.
KNOW MORE
Open loop current sensor based on the principle of Hall-effect. It can measure the AC signal current under the condition of electrical isolation and convert it into DC signal output.
KNOW MORE
Open loop current sensor based on the principle of Hall-effect. It can measure the AC signal current under the condition of electrical isolation and convert it into DC signal output.
KNOW MORE
Open loop current sensor based on the principle of Hall-effect. It can measure the AC signal current under the condition of electrical isolation and convert it into DC signal output.
KNOW MORE
The current sensor using the principle of electromagnetic induction can measure the AC signal current under the condition of electrical isolation, and output 4-20mA DC current output proportional to the effective value of the measured current. They require only a two-wire connection and do not require a separate loop power supply.
KNOW MORE
The current sensor using the principle of electromagnetic induction can measure the AC signal current under the condition of electrical isolation, and output 4-20mA DC current output proportional to the effective value of the measured current. They require only a two-wire connection and do not require a separate loop power supply.
KNOW MORE
Open loop current sensor based on the principle of Hall-effect. It can measure the AC signal current under the condition of electrical isolation and convert it into DC signal output.
KNOW MORE
The current sensor using the Hall effect open-loop principle can measure DC, AC, pulse and various irregular waveforms of current under the condition of electrical isolation.
KNOW MORE
Open loop current sensor based on the principle of Hall-effect.It can be used for measuring AC,DC,pulsed and mixed current.
KNOW MORE
A new type of current sensor based on the principle of magnetic modulation has good stability of small current, high insulation between primary and secondary, and strong anti-interference ability. After signal conversion, it can be directly collected and accepted by PLC, secondary instrument and other acquisition devices, and is used in signal system, line detection, leakage monitoring system, current difference measurement.
KNOW MORE
A new type of current sensor based on the principle of magnetic modulation, which can measure the current of mA level small signal DC under the condition of electrical isolation.
KNOW MORE
A new type of current sensor based on the principle of magnetic modulation ,which can measure the current of mA level DC small signal under the condition of electrical isolation.
KNOW MORE
D-FS050LD/60 series DC leakage current sensor is a new type of current sensor developed by magnetic modulation principle. It has good stability of small current and high insulation between primary and secondary. Used in signal system, line detection, leakage monitoring system, current difference measurement.
KNOW MORE
Applying Hall effect and closed-loop Hall measurement principle, after TRCSM calculation, the measured current is converted into a DC current or voltage measurement module proportional to the output of the primary current, and the mixed current such as AC and DC is measured, and the primary and secondary sides are highly insulated. It has the characteristics of high accuracy, high linearity, high integration, small size, simple structure, easy installation, long-term stability and adapt to various working environments. Widely used in electric power, petroleum, coal, chemical, railway, communication, building automation and other industries of electrical equipment system control and testing.
KNOW MORE
Using Hall effect and open-loop measurement principle, after TRMS calculation, the measured current is converted into DC current or voltage output proportional to the primary current, and the current sensor can measure DC, AC, pulse and various irregular waveforms of current under the condition of electrical isolation. It has the characteristics of high accuracy, high linearity, high integration, small size, simple structure and long-term stability.
KNOW MORE
Using Hall effect and open-loop measurement principle, after TRMS calculation, the measured current is converted into DC current or voltage output proportional to the primary current, and the current sensor can measure DC, AC, pulse and various irregular waveforms of current under the condition of electrical isolation. It has the characteristics of high accuracy, high linearity, high integration, small size, simple structure and long-term stability.
KNOW MORE
The LTR5 series sensor is an open-loop current sensor based on the Hall principle that can measure DC, AC, pulse and various irregular currents. The output of the sensor can truly reflect the real waveform of the energized conductor.
KNOW MORE
FSM4005 Current sensor is a closed loop device based on the measuring principle of the hall effect and null balance method,with a galvanic isolation between primary and secondary circuit,the size of primary not affect test precision,no matter the location of primary in the hole of current sensor.It can really measure resolution 3000:1 and it uses for precision measurement of DC,AC and pulse current
KNOW MORE
Hi! Welcome back.
How are you doing?
Let’s talk! We’ll provide the perfect solution for you！
Shanghai Freesor Sensor Technology Co. ,Ltd. was founded in 2005 by a number of overseas returnees with rich experience. It is a high-tech enterprise integrating design, research and development, production and sales.
Sales Center Add: Room 1405-1, Building B, 333 Haiyang 1st Road, Pudong New Area, Shanghai
Factory Add:Building 4, Keland Smart Energy Industrial Park, Guangming District, Shenzhen, Guangdong Province, China.
English
Russian
Chinese
